Featured Archives - Pike Industries

Pike Industries 400 Amp Solid Copper Busbar 4 Stud (5/16″ Stainless, Red) Common Bus, Terminal Block

matt — Fri, 09 Feb 2024 16:26:24 +0000

Solid copper BusBar for RV, boat & Marine, home, and automotive use in 12-48 volt DC applications. 400 Amp rated, continuous duty cycle, designed to meet increased ampacity requirements when 3000W 12V Inverters are fed by multiple sources through a common busbar, (solar, battery, generator, etc..) Fully rebuildable injection molded ABS Insulator is designed for maximum stability with a wide 4 hole mounting base, (mounting screws included), and impact resistance. High quality materials used for studs, flange nuts, and mounting fasteners. Standard duty models use Grade 5 or higher, Zinc plated steel fasteners, and Marine rated models use 316 Stainless Steel hardware (316 stainless alloy is suitable for saltwater and corrosive environments whereas 304 stainless used by other manufacturers requires frequent cleaning)

The post Pike Industries 400 Amp Solid Copper Busbar 4 Stud (5/16″ Stainless, Red) Common Bus, Terminal Block appeared first on Pike Industries.

Victron Energy Orion-Tr Smart 24/24-Volt 12 Amp 280-Watt DC-DC Charger Isolated (Bluetooth)

matt — Fri, 09 Feb 2024 16:26:22 +0000

Victron Energy Orion-Tr Smart Isolated DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth. For use in dual battery systems in vehicles or on boats where the (smart) alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch and has an engine running detection mechanism. Victron Energy Orion Tr-Smart DC-DC charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power. If required, Bluetooth can be disabled.

The post Victron Energy Orion-Tr Smart 24/24-Volt 12 Amp 280-Watt DC-DC Charger Isolated (Bluetooth) appeared first on Pike Industries.

Victron Energy SmartSolar MPPT Tr VE.Can 250V 100 Amp 12/24/36/48-Volt Solar Charge Controller (Bluetooth)

matt — Fri, 09 Feb 2024 16:26:22 +0000

Victron Energy SmartSolar MPPT solar charge controller: A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, Victron Energy SmartSolar MPPT solar charge controller maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. Victron Energy SmartSolar MPPT solar charge controller maintains battery health, extending its life. Victron Energy SmartSolar MPPT charge controller will even recharge a severely depleted battery. It can operate with a battery voltage as low as 0 Volts, provided the cells are not permanently sulphated or otherwise damaged. Battery voltage: 12/24/48V Auto Select (software tool needed to select 36V).

The post Victron Energy SmartSolar MPPT Tr VE.Can 250V 100 Amp 12/24/36/48-Volt Solar Charge Controller (Bluetooth) appeared first on Pike Industries.

Victron Energy MultiPlus-II 2X 120V 3000VA 12-Volt Pure Sine Wave Inverter and 120 amp Battery Charger

matt — Fri, 09 Feb 2024 16:26:21 +0000

The MultiPlus-II 2 x120V is the perfect one-box mobile solution for standard North American 50A 120/240VAC split-phase applications. Whether it is supplied from shore power or a generator, the MultiPlus-II 2x120V can accept and passthrough both lines of a 120/240V supply, with the capability to utilize the full 50A for charging and AC loads. When connecting to a single phase 120V supply, the L1 input of the MultiPlus-II 2x120V will accept incoming power for charging and passthrough, while combining the L1 and L2 outputs for single-phase 120V on each line.

The MultiPlus switches to inverter operation when no AC source is available. The inverter output is also 120V single phase. In inverter mode, the MultiPlus-II 2x120V internally connects both lines L1 and L2 together to provide 120VAC to loads on either output. Therefore, in all connection circumstances, both sides of a distribution panel will be supplied with 120V. However, 240VAC is only available when the MultiPlus is supplied by a split phase 120/240VAC source. This prevents heavy loads such as water heaters or 240V air conditioners from discharging the battery.

The MultiPlus-II 2x 120V has all of the expected features of our versatile inverter/charger range, including PowerControl, PowerAssist, Input Current Limit, two AC outputs, as well as parallel and 3ph configuration for larger capacity VE.Bus systems. Suitable for LiFePO4 batteries and a variety of other battery technologies.

The post Victron Energy MultiPlus-II 2X 120V 3000VA 12-Volt Pure Sine Wave Inverter and 120 amp Battery Charger appeared first on Pike Industries.